ASTM A480 PDF

ASTM A is the specification that covers the general requirements for flat- rolled stainless and heat-resisting steel plate, sheet and strip. It does not reference. 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel, product specifications that reference Specification A/. ASTM A/AM Standard Specification for General Requirements for Flat -Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and.

Author: Shakalar Goltimuro
Country: Morocco
Language: English (Spanish)
Genre: Technology
Published (Last): 5 February 2009
Pages: 479
PDF File Size: 2.56 Mb
ePub File Size: 13.29 Mb
ISBN: 335-4-62659-842-4
Downloads: 61713
Price: Free* [*Free Regsitration Required]
Uploader: Mushicage

All widths and lengths 1 16 18 1 16 18 Over mm 1. NOTE asym measurements are taken at least 10 mm in from the edge of the product, except that on widths less than 26 mm, the tolerances are applicable for measurements at all locations.

Link to Active This link will always route to the current Astn version of the standard. Retests and Retreatment Historical Version s – view previous versions of standard. Open clean defects, such as pits or impressions, will not necessarily require preparation. Approved December 1, The presence of an unspeci?

Test data from a minimum of three test lots, as de? For S, see Note 6.

Edges for Cold-Rolled Strip Finish for Strip When intergranular corrosion tests are required, they shall be as agreed upon between the seller and the purchaser. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

ASTM A480 Specification

The steel shall have no imperfections of a nature or degree, for the type and quality ordered, that will adversely affect the stamping, forming, machining, or fabrication of? Typically, very faint buff of polish lines may still be visible on the?

  DOA RATIB HADDAD PDF

Blending after part assembly may be done with buffing. Permitted Variations in Dimensions and Weight 9.

In the case of polished? Heat and product analyses shall conform to the chemical requirements for each of the specific elements. C Not including hard tempers of 2xx and 3xx series, dead-soft sheets, and deep-drawing sheets.

Quenched in water or rapidly cooled by other means at a rate sufficient w480 prevent reprecipitation of carbides, as demonstrable by the capability of passing the test for resistance to intergranular corrosion speci? In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the wstm order shall prevail. Bright Annealed Finish—See Note 4.

However, it is not necessary to actually run the tests unless speci?

ASTM A480 Plate Thickness & Flatness Tolerances

The material shall undergo mechanical tests such as tension test, hardness test, and bend test. When the material is too thin to allow hardness testing using any of the Rockwell super? Notwithstanding the absence of a signature, the organization submitting the EDI transmission is responsible for the content of the report. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but zstm not provided as part of the standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

The manufacturer is permitted, if necessary, use a lower temperature resolution anneal or a stabilization anneal after a high temperature solution anneal in order to meet corrosion test requirements. It is produced by buffing a? Widths up to 48 [] excl Widths 48 [] and over Lengths up to [] excl Lengths [] and over For thicknesses 0. Refer to Section Committee A01 has identi? The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product speci?

  DESCARGAR ANATOMIA DE ROUVIERE TOMO 2 PDF

Note that for aa480 applications user may wish to specify minus rather than plus tolerance or vice versa. NOTE 1—A typical ordering description is as follows: In the case of transverse bend test specimens, the axis of bend shall be parallel to the direction of rolling.

Use of this method shall be by agreement between purchaser and supplier. Various production methods may be used to obtain these?

ASTM A Specification | Penn Stainless Products

The applicability of these tests to duplex stainless steels not listed in Test Methods A shall be a matter for negotiation between the seller and the purchaser.

For plates up to mm, incl, in thickness, the tolerance under the speci? In the case of heavier plates z480 types other than L, LN, Cb, Cb, Cb, L, LN, Ti, L,S, and S, the applicability of this test shall be a matter for negotiation between the seller and the purchaser.

Permission rights to photocopy the standard may also be secured from the ASTM website www.