EN 1757-3 PDF

Europastandarden EN gäller som svensk standard. The European Standard EN has the status of a Swedish. Standards. DIN EN Safety of industrial trucks – Pedestrian propelled manual and semi-manual trucks – Part 3: Platform trucks; German version EN. DIN EN Safety of industrial trucks – Pedestrian propelled manual and semi-manual trucks – Part 3: Platform trucks.

Author: Moogushakar Kajir
Country: Greece
Language: English (Spanish)
Genre: Spiritual
Published (Last): 8 October 2018
Pages: 102
PDF File Size: 3.57 Mb
ePub File Size: 4.99 Mb
ISBN: 332-9-36325-232-7
Downloads: 6107
Price: Free* [*Free Regsitration Required]
Uploader: Kajizahn

With the truck stationary, measurement consists of recording the maximum force applied tangentially in the middle of the handle throughout the steering lock in one direction from the tiller’s axial position Figure A.

Find Similar Items This product falls into the following sn.

NBN EN 1757-3

When provisions of this type C standard are different 157-3 those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard. Learn more about the cookies we use and how to change your settings.

Search all products by. The force shall be applied horizontally along the truck’s axis on the tiller handle or bar. The truck shall be on substantially firm and level ground and may be anchored to prevent overturning. Specific requirements for the electrical power transmission systems of internal combustion engine powered trucks EN Safety of industrial trucks – Self propelled variable reach trucks EN Safety of industrial trucks – Driverless trucks and their systems EN Safety of industrial trucks – Additional requirements for automated functions on trucks EN Safety of industrial trucks – Self propelled trucks over 10 kg capacity EN Safety of industrial trucks – Self propelled trucks up to and including 10 kg capacity and tractors with a drawbar pull up to and including 20 N Part 1: Hazards Corresponding requirements 4.

Chariots a plateau fixe Title in German Sicherheit von Flurfoerderzeugen. Vertical bars shall have a vertical length of at least mm. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member.

  DOD 1327.5 PDF

With the aim of clarifying the intention of the standard and avoiding doubts when reading it, the following assumptions were made when producing it: NOTE The forces to operate the truck are varying with the value of the load, the ground conditions and the truck conditions.

BS EN Safety of industrial trucks — Self-propelled trucks up to and including 10 kg capacity and industrial tractors with a drawbar pull up.

General requirements for internal combustion engine powered trucks Part 3: In case of incorrect operation, the truck shall be adapted until the test is successful.

The corresponding requirements are designed to limit the risk or reduce these hazards in each situation.

The efforts shall be measured in accordance with the methods described below for all the values of load indicated in Table 1 which are less or equal to the rated capacity and located according to 6. The test is successful if measured values do not exceed those laid down in Table 1.

BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. A series of longitudinal and lateral stability tests shall be carried out depending on the truck type with the positions of the truck on the platform as below and Table B. The test load, where applicable, shall be applied according to clause 3. A list of organizations represented on this committee can be obtained on request to its secretary.

The hand grips shall be of a cross section enclosed within the space between two concentric circles of 25 mm inside diameter and 35 mm outside diameter and provide a minimum span of mm for each hand. Industrial trucks, Materials handling equipment, Hand trucks, Equipment safety, Safety engineering, Commercial road vehicles, Pedestrian-controlled systems, Platforms, Hazards.

BS EN 1757-3:2002

Copyright Copyright subsists in all BSI publications. During measurement the lower surface of the tiller handle shall be maintained at a height of mm above the ground. When pulling the horizontal distance between the end of the tiller and the front of een wheel Figure 2 shall be more than mm, the handle axis being positioned within mm to 1 mm height.


The test shall be carried out with a new truck chosen according to 6.

The upper part of the tiller handle shall conform to the dimensions shown in Figure 1 and Figure 2. Two tests in both the forward and reverse directions shall be carried out and the average result recorded.

It is incorporated by Royal Charter.

BS EN – Safety of industrial trucks. Pedestrian propelled trucks. Platform trucks

The machinery concerned and the extent to which hazards, hazardous situations and e are covered are indicated in the scope of this document. It presents the UK view on standards in Europe and at the international level.

The frequency of the load handling cycle should also be taken into account.

Compliance with a British Standard does not of itself confer immunity from legal obligations. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Mayand conflicting national standards shall be withdrawn at the latest by May This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3. Additional requirements for trucks with elevating operator position and trucks specifically designed to travel with elevated loads EN Safety of industrial trucks – Operation in potentially hazardous atmospheres — Use in inflammable gas, vapour, mist and dust EN Safety of industrial trucks – Pedestrian propelled trucks Part 1: Two measurements are recorded in each direction of bar steering.

Take the smart route to manage medical device compliance. This series of standards includes: Except as permitted under the Copyright, Designs and Patents Act no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means — electronic, photocopying, recording or otherwise — without prior written permission from BSI.

General requirements Part 2: Handbetriebene und teilweise handbetriebene Flurfoerderzeuge. Information regarding online access to British Standards via British Standards Online can be found at http: