INTERSEAL 670HS MSDS PDF

INTERSEAL HS – PART B (REGULAR) – L () Use; Colors; MSDS / TDS; Variant; Product Review(s). Use For immersion service, Interseal HS must be applied to surfaces blast cleaned to SSPC-SP10 or Sa PT. International Paint Indonesia. Safety Data Sheet EGA INTERSEAL HS GREY PART A Version Number 2 Revision Date 06/27/ 1. Product and . International Paint Ltd. Safety Data Sheet. EGA Interseal HS Grey Part A. Version No. 2 Date Last Revised 05/10/ Conforms to the requirements of.

Author: Dira Fenririsar
Country: Kosovo
Language: English (Spanish)
Genre: Marketing
Published (Last): 21 December 2010
Pages: 21
PDF File Size: 2.90 Mb
ePub File Size: 3.38 Mb
ISBN: 512-2-25162-782-4
Downloads: 2230
Price: Free* [*Free Regsitration Required]
Uploader: Gardakree

A surface profile of mils microns is recommended.

With freshly blasted surfaces a slight degree of flash rusting is allowable, and is preferable to the surface being too wet. Loose or flaking coatings should be removed back to a firm edge. However, it can be used over suitably primed surfaces. Surface preparation The msdz of this product will depend upon the degree of surface preparation. Systems recommendation Interseal HS will normally be applied to correctly prepared steel substrates.

Please consult International Protective Coatings for alternative recommendations. Intereal, this product is not recommended where thermoplastic coatings such as chlorinated rubbers and vinyls have previously been used.

Interseal HS is suitable for overcoating intact, aged alkyd, epoxy and polyurethane systems. Avoid using a mixture of application methods whenever possible. Warning In order to achieve optimum performance on hand prepared steel, the aluminum pigmented version should be applied as a primer coat inyerseal brush to ensure thorough wetting out of the substrate by Interseal HS.

  INTRODUCTION TO PARALLEL ALGORITHMS JAJA PDF

Level of sheen and surface finish is dependent on application method.

INTERSEAL HS PLATINUM GREY MSDS Download

If salt water is used in the wet blast process the resulting surface must be thoroughly washed with fresh water before application of Interseal HS. Provides excellent anti-corrosive protection in industrial, coastal structures, pulp and paper plants, bridges and offshore environments in both atmospheric exposure and immersion service.

Brush Typically mils microns can be achieved Roller Typically mils microns can be achieved How to use Mixing Material is supplied in two containers as a unit. Further information is available from International Protective Coatings. Alternatively, a broadcast method of application can be used.

Premature exposure to ponding water will cause a color change, especially in dark colors.

intersel Typically this would apply to C or D grade rusting in this standard. Once the unit has been mixed it must be used within the working pot life specified. Preferred application is by a suitable large tip hopper gun e. When applying by methods other than airless spray, the required film build is unlikely to be achieved. Dry bristle brushing will normally be adequate for accumulated dirt.

INTERSEAL 670HS – PART B (REGULAR) – 0.57L (5.63 :1)

The imterseal to be coated should be clean, dry and free from contamination. Soluble salts should be removed by fresh water washing. However, these phenomena are not detrimental to anti-corrosive performance. Varnish Hybrid Water base. NSF Certification is for tanks greater than gallons Press and move to zoom. Be the first to write a review for this product!

  ARISTON AML 101 PDF

Consult International Protective Coatings for further details. Mouse over image to zoom.

Accumulated dirt and soluble salts must be removed. In common with all epoxies Interseal HS will chalk and discolor on exterior exposure. A low VOC, two component high build, high solids surface tolerant epoxy maintenance coating.

Low or high temperatures may require specific application techniques to achieve maximum film build.

Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner. Trowel or roller can ksds used for small areas.

Typical thicknesses will be between milsmicrons. Sagola or Air texture gun fitted with a mm nozzle. Certification is for tanks greater than gallons Do not thin more than allowed by local environmental legislation.

INTERSEAL HS – PART B (REGULAR) – L ( :1)

For application to a wide variety of substrates including hand prepared rusty steel, abrasive blast cleaned and hydroblasted steel, and a wide range of intact, aged coatings. Aged Coatings Interseal HS is suitable for overcoating a limited range of msxs, tightly adherent aged coatings.

Puddles, ponding and accumulations of water must be removed.